[vyřešeno] tp-link 1043ND - port forwarding

[karlos00x]

chapu spravne, ze v origo firmware pro tento router neumim nastavit toto:
- prichozi komunikaci na portu 13391 posunuj na 10.0.0.1:3389
- prichozi komunikaci na portu 13392 posunuj na 10.0.0.2:3389
? tedy vzdalena plocha na dva ruzne kompy bez nutnosti resit vpn apod.

lze to jednoduse nastavit ve WRT? ktery WRT doporucite(vim, ze nekdo to tady ma) open nebo dd?

[soban]

V dd-wrt všechno naklikáš.
V Open-wrt základ taky naklikáš - ovšem pro speciality potřebuješ příkazovou řádku, ovšem zase můžeš ovládat - dělat cokoliv.

Já jsem kdysy používal dd-wrt od BrainSlayera odsud http://www.dd-wrt.com/site/support/othe ... %2F2012%2F

Ovšem jak jsou se stabilitou nové verze nevím - přešel jsem na Openwrt.

[Mike.M]

Takyto forward umi snad kazdy orogo fw. Menuje se to virtualserver. A umi to.

Soban: jinak ja taky s dd presel na open.

[karlos00x]

http://www.tp-link.com/simulator/TL-WR1043ND/index.htm
a jak presne to tam teda mam naklikat? me jde jen nastavit prichozi 3389 -> 10.0.0.1:3389 ale to nechci.
Ale nikde tam nevidim moznost zadat:
prichozi port => cilova IP:jiny-port

[Slondo]

Forwarding->Virtual Serve

Virtual Servers Help

Virtual servers can be used for setting up public services on your LAN. A virtual server is defined as a service port, and all requests from Internet to this service port will be redirected to the computer specified by the server IP. Any PC that was used for a virtual server must have a static or reserved IP address because its IP address may change when using the DHCP function.
Service Port - The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX - YYY, XXX is Start port, YYY is End port).
Internal Port - The Internal Service Port number of the PC running the service application. You can leave it blank if the Internal Port is the same as the Service Port, or enter a specific port number when Service Port is a single one.
IP Address - The IP address of the PC running the service application.
Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols supported by the Router).
Status - The status of this entry, "Enabled" means the virtual server entry is enabled.
Common Service Port - Some common services already exist in the pull-down list.
Modify - To modify or delete an existing entry.

[karlos00x]

slondo zkusil jsi prosim Te to demo co jsem odkazoval? Je tam pouze jeden input na port a jeden na IP. kde jsi vzal tuhle napovedu?

[Slondo]

Demo som neskúšal,
Firmware: TL-WR1043ND_V1_120405

[Mike.M]

Service potr das 13389 a internal 3389 na ip 10.0.0.1
Dale das 23389 a internal 3389 na ip 10.0.0.2

[Slondo]

karlos00x:

- prichozi komunikaci na portu 13391 posunuj na 10.0.0.1:3389
- prichozi komunikaci na portu 13392 posunuj na 10.0.0.2:3389

teda
Service Port: 13391, Internal Port: 3389, IP Address: 10.0.0.1 a
Service Port: 13392, Internal Port: 3389, IP Address: 10.0.0.2

[Mike.M]

Ano. Starsi fw to asi neumely, v tom demu chybi smerovani na port, ale v tvem obrazku uz to je. Jinak ddwrt je prehlednejsi a nahrava se stejne jako origo fw. Ma ale omnoho vice moznosti.

[karlos00x]

chlapy, uplne blbej nejsem

mel jsem to jako v tom demu tedy jen jeden input pro zadani portu. Ted jsem upgradoval firmware na ten doporuceny slondem a uz to tam mam.

Co me mile prekvapilo tak to zkouslo i restore configu ze starsiho firmware.

-- 6. 5. 2012 11:36 --

jo a diky vam oběma.